Faria Instruments GM/ALDL Bedienungsanleitung

GM ALDL MG2000™ TachometerIS0195rev. A ecr#5576 8/2005Owner’s Manual

Page 6This page left blank intentionally.

Edit ModeThe “Edit” mode is used to adjust or set the values of numerous functions and options in the MG2000. The procedure below specifies th

1DisplayNextScreen23Press and hold the “Up” and “Down” buttons for 2 seconds to select this screen as the “default screen” and exit.Press “Up” or “Dow

Set “Amount of Fuel”1SetAmountOf Fuel23NOTE: If a known amount of fuel is in the fuel tank but it is not full, this function can be used to indicate t

Press and hold the “Up” and “Down” buttons for 2 seconds to save selection for Screen 1, line 1 and advance to Screen 1, line 2.Press “Mode” to exit w

Press and hold the “Up” and “Down” buttons for 2 seconds to select “Oil Pressure Dial.”Press “Up” or “Down” to select another “Gauge Range.”Press “Mod

Select “Water Press Dial”1SelectWater PressDial23Press and hold the “Up” and “Down” buttons for 2 seconds to select “Water Press Dial.”Press “Up” or “

Press “Up” or “Down” to scroll through the selections.When the correct choice is next to the selection arrow, Press and hold the “Up” and “Down” butto

Press “Up” or “Down” to scroll through the selections.When the correct choice is next to the selection arrow, Press and hold the “Up” and “Down” butto

Press “Up” or “Down” to scroll through the selections.When the correct choice is next to the selection arrow, Press and hold the “Up” and “Down” butto

IS0195 x7 w/ correctionsMark ups 12/20/05

If there is no tank size available in the list that matches your tank size, scroll to the next screen.1SelectOtherFuel TankSize234Press “Up” or “Down”

Page 17Press and hold the “Up” and “Down” buttons for 2 seconds to save “Full Tank” calibration and exit.Press “Up” or “Down” to select another functi

This screen will display for 10 seconds.The horn will sound three times.The warning lights will flash three times.The backlights will flash three times.

Alarm Mode LINE DISPLAYThe “Alarm” screen will appear if a loc

Press and hold “Up” and “Down” for 2 seconds to view alarm messages.Press “Mode” to silence alarm horn and return to “Run” mode. LED will continue to

MANIFOLD AIR SENSOR1MAN AIRSENSORSEE DEALER23THROTTLE POSITION SENSOR1TPSFAULTSEE DEALER23COOLANT SENSOR1COOLANTSENSORSEE DEALER23ENGINE ECU CABLE NOT

Page 22MG2000 Tachometer654321789101112123654ALDLHarness HN0390ALDLTachometer Cable4- pin connector12- pin connectorPin A RedPin B WhitePin C Green

654321789101112123654MG2000 SpeedometerHarness HN0390Speedometer Cable1 2 3 4 5 6 7 8 9 10 11 12Wire Jacket12- pin connectorPin 1 RedPi

RED - IGNITIONMG2000 Tachometer 654321789101112123654NMEA 2000Harness HN0401NMEA 0183 Cable6- pin connectorPin 1 Not UsedPin 2 Not UsedPin 3 Red/

Tachometer to 2” Gauge ConnectionPJ0018 Note: To help reduce moisturein the gauges, be sure to install plug PJ0018 in all open connectors2" Gauge

IndexFigure 1 Default screens page 1Description page 1Normal Mode page 2 Contrast and Lighting page 2 Displayed Functions page 3 Default scr

Notes:

Copyright 2005 by the Thomas G. Faria Corporation, Uncasville CT. All rights reserved. No part of this publication may be reproduced in any form, in a

This page left blank intentionally.

The FARIA MG2000 Tachometer combines the features of an ECU serial bus gateway and several instruments into one unit:• The tachometer is an

(see Figure 2). Press the “Mode” button to exit the “screen selection mode” and return to “Normal” mode or do not push any buttons for 4 second

To adjust the lighting intensity of all of the instruments in the system, press and hold both the “Down” and “Up” buttons for 2 seconds.

Displays the Engine Hours data received from the engine ECU.Default screen “4”This screen displays fault conditions based on engine data received

1. Select Default Screen2. Reset Fuel Used3. Set Fuel Tank Full4. Set Amount of Fuel5. Organize User Screens6. Select Gauge Range7. Select Fuel